GE Universal Remote Manual PDF

GE Universal Remote Manual PDF Download

GE Universal Remote Manual PDF Download for free using the direct download link given at the bottom of this article.

GE Universal Remote Manual PDF Details
GE Universal Remote Manual
PDF Name GE Universal Remote Manual PDF
No. of Pages 32
PDF Size 11.31 MB
Language English
CategoryEnglish
Source pdfsource.org
Download LinkAvailable ✔
Downloads17

GE Universal Remote Manual

Dear friends, here we are going to offer GE Universal Remote Manual PDF for all of you. The GE Universal Remote Control is one of the most easy-to-use remote controls which is available today. With the GE Universal Remote Control, juggling multiple remote controls is a thing of the past.

Your GE Universal Remote Control controls multiple devices, including the most popular brands of TV, VCR, DVD, CBL, and SAT. The GE Universal Remote Control is easy to use, and easy to program, and it gives you total control at the touch of your fingertips.

GE Universal Remote Manual PDF

Your universal remote requires two (2) AAA batteries (not included). Alkaline batteries are recommended.

Battery Installation

1. On the back of the remote, pull down on the textured surface and slide the battery cover downward to remove it.

2. Match the (+) and (-) marks on the batteries to the (+) and (-) marks inside the battery compartment, then insert two (2) AAA batteries. Be sure to use fresh batteries.

3. Position the battery cover slightly below the opening and push upward to lock it into place.

NOTE: If your remote stops operating properly, replace the batteries with new ones.

Battery Precautions

  • Do not mix old and new batteries.
  • Do not mix alkaline, standard (carbon-zinc), or rechargeable (Ni-Cd, Ni-MH, etc.) batteries.
  • Always remove old, weak or worn-out batteries promptly and recycle or dispose of them in accordance with local and national regulations.

Battery Saver

Your remote automatically turns off if the buttons are depressed for more than 8 seconds. This will save your batteries should your remote get stuck in a place where the buttons remain depressed (e.g., between the sofa cushions).

Code Saver

You have up to 10 minutes to charge the batteries in your remote without losing the codes you have programmed.

Programming Notes

  • If your device does not respond to the remote after trying all codes listed or your brand is not listed in the code list, use the Auto Code Search method to program your remote.
  • Sometimes the first code that “works” with your device may operate only a few functions of your device. There may be another code in the code list that performs more functions. Try other codes from the code list for more functionality.
  • With the Direct Code Entry method, you can program any device button to control any device in your home entertainment system. For example, you can use the DVR or AUX device button to control an audio receiver or a DVD, VCR, satellite device, etc.
  • For combination devices, you may have to enter a code for each device. For example, for a VCR/DVD device, you may have to enter a code for the DVD under the DVD button and enter a code for the VCR using a different device button on the remote.
  • Write down the code found to operate your device for future reference.

GE Universal Remote Manual Code List

Auto Code Search

The Auto Code Search searches automatically through the codes stored in this remote. Read all the following steps prior to starting the auto code search as you will need to be prepared to lock in the proper code when found.

  1. Manually turn on the device you wish to control.
  2. Press and hold the SETUP button until the red indicator light stays on (approximately 2 seconds) and then release the button.
  3. Press and release the desired device button on the remote (TV, CBL, DVR, DVD, SAT, AMP, AUX 1, AUX 2) the type of device you wish to control. The red indicator will blink once and then remain on.
  4. Point the remote at the device and press and release the POWER button (for TV) or PLAY button (for DVD, VCR, etc.) to start the search. The red indicator will flash (approximately every 2 seconds) as the remote searches. Note: The remote must be pointed at the device for the duration of this search.
  5. Place your finger on the #1 button so you are prepared to lock in the code.
  6. When the device shuts off or begins playing, press the #1 button to lock in the code. The red indicator light will
    turn off. Note: You have approximately two seconds after the device shuts off or begins playing to lock in the code.
  7. Point the remote at the device and check to see if the remote operates the device as desired. If it does, no
    further programming is required for that device. If it does not, return to step 2 and start the auto code search again.
  8. Repeat this process for each device (for example TV, DVD, SAT, AUX) in your home entertainment system you wish to control.

You can download GE Universal Remote Manual PDF by using the following download button.


GE Universal Remote Manual PDF Download Link

RELATED PDF FILES