Program Universal Remote PDF

Program Universal Remote PDF Download

Program Universal Remote PDF Download for free using the direct download link given at the bottom of this article.

Program Universal Remote PDF Details
Program Universal Remote
PDF Name Program Universal Remote PDF
No. of Pages 12
PDF Size 1.70 MB
Language English
CategoryGeneral
Source pdfsource.org
Download LinkAvailable ✔
Downloads17

Program Universal Remote

Hello friends, here we are going to upload Program Universal Remote PDF for all of you. A universal remote can be programmed to be used with multiple devices like TV, Blu-Ray and AV Receivers, you can ditch several different remotes for one Universal remote.

Universal remote can control all home theatre devices and components. A universal remote allows you to set aside the individual device remotes for one Universal remote. With a universal remote you can start using it by first programming the remote with each individual device in the home theatre arsenal.

Program Universal Remote PDF

1. Important Information About Your Remote

Your remote is initially programmed to only operate your set-top box. Therefore, you must program the remote to operate your TV, VCR, DVD, or other devices. See PROGRAM THE REMOTE TO CONTROL MY DEVICES to learn how to enter device codes and program your remote.

NOTE: You must use the IR remote within line of sight of the set-top box to operate the set-top box correctly.

2. How Does A UNIVERSAL REMOTE CONTROL WORK?

You tell the remote which type of device you want to operate using the four keys arched across the top of the remote. These keys, known as mode keys, are labelled STB (Set-Top Box), TV, DVD, and AUX. Each mode key is associated with a specific device. As an example, after programming the remote, if you want the remote to operate your TV, you simply press the TV key.

Other keys you press on the remote, thereafter, should operate your TV. Want to switch the remote to operate a different device? Just press the mode key for the next device you want to operate. In this guide, you will learn which
types of devices you can control and how to program the remote to control your specific devices.

3. Where Do I Start?

Before you begin using your remote, complete the following initial setup tasks.

  • INSTALL THE BATTERIES:
    The remote requires two AA batteries (alkaline recommended). A diagram in the battery compartment of the remote indicates the proper placement of the batteries. When the batteries are properly installed, the light on the remote blinks each time a key is pressed.
  • VISIT THE REMOTE CONTROL QUICK REFERENCE SECTION:
    Use the Remote Control Quick Reference section on Page 12 of this guide to familiarize yourself with the remote and the functions of its various keys. Knowing the function and location of the keys on the remote will assist you when you are programming the remote.

4. Program the Remote

To learn how to program your remote, refer to the sections What Devices Can I Control, What Devices Do I Want to Control, and Program The Remote To Control My Devices for further instructions.

5. Find A Place To Store Your Remote

Keeping up with one remote is much easier than keeping up with four or five remotes. However, it is still a good idea to find a storage location for your remote. The AT6400 is not a toy. It should be kept out of the reach of children under the age of 6 years.

6. Program The Remote To Control My Devices

Your remote is initially programmed to only operate your Set Top Box. You will need to set up the remote to operate your other devices using its TV, DVD, VCR, and AUX modes. The TV key may be programmed to operate a standard or high-definition television (HDTV).

The DVD key may be programmed to operate a DVD player. The AUX key may be programmed to operate a VCR, a receiver, an amplifier, or a Home Theater in a Box (HTIB) system. If the remote provides only limited functionality for a device, you can look for a code that provides more functionality. Refer to the code tables at the end of this guide to locate additional programming codes.

Note: You have the option to assign some remote keys to operate one device type only. For example, you may want to assign volume control to the TV only. If this is the case, you can reprogram power, volume, and channel control using procedures found later in this guide.

7. Assigning A Device Code To A Mode Key

Refer to the code tables at the end of this guide to locate the information for the device you want to control.

NOTE: If your device is not listed, you may be able to program the remote using the Auto-Search function. Go to What If None of the Codes Work on page 15 for instructions.

1. Turn on the device that you want to assign a mode key.

2. Press and hold the appropriate mode key (TV, DVD, or AUX) on the remote, and then press and hold the OK key.

3. Release both keys and the mode keys blink twice.

4. Enter the first 4-digit setup code for the device using the numeric keys (0-9) on the remote.
The mode key blinks three times to indicate that the code entry was accepted.

Notes:

  • When an invalid code is entered, the selected mode key displays a long flash to indicate
    that you have not entered the code correctly.
    Should the remote time out before you complete the code setup, you must start over.
    This is indicated by one long flash of the red LED.

5. Point the remote at the device, and press POWER to test the device.

6. Did the device power off?

  • If YES, write this code number in the table found on page 38. You may need it again if the device code is accidentally erased.
  • If NO, repeat this procedure from step 3 using a different setup code.

Note: If none of the codes listed for your brand of device operates the device correctly, go to What If None of the Codes Work for instructions.

7. Repeat this procedure for each mode key you want to program.

8. WHAT IF NONE OF THE CODES WORK?

If none of the codes listed for your brand of device operates the device correctly, or if your device is not listed in the codes table, you can use the Auto-Search function to search through the code library for a valid code. This section provides procedures for using the Auto-Search function to search the code library for TV, DVD, and AUX mode codes.

NOTE: Read the procedures in this section thoroughly before beginning. You need to be prepared to
observe the behaviour of the remote.

Auto-Search Features

Consider the following items when using Auto-Search:

  • The Auto-Search function begins searching from the first code.
  • If a valid code is not found, the green backlight blinks twice and the remote returns to normal operation.
  • If any other key is pressed except PLAY, ENTER, POWER, EXIT, REW, FF, or numeric keys 1 through 4 (when programming the AUX mode key), the mode key displays a long red flash (error message) and the remote returns to normal operation.
  • Should the remote time out before you complete the Auto-Search function you must start over. This is indicated by one long flash of the red LED.
  • If the device is not listed and the Auto-Search function is unable to find a usable code, you may need to use the original remote provided with the device.

AUTO-SEARCHING THE CODE LIBRARY FOR TV OR DVD MODE CODES (Program Code 922)

NOTE: This procedure only applies to TVs and DVDs.

1. Turn on the device that you want to assign to the TV or DVD key.

2. Point the remote at the device.

3. Press and while holding a selected mode key (TV or DVD), press the OK key. For example, to search for a TV code, press and hold the TV and OK at the same time.

4. Release both keys and all the mode keys will blink twice.

5. Enter the programming code 922 by pressing the numeric keys on the remote. The mode key you selected in step 3 blinks twice to indicate a successful entry.

6. Point the remote toward the device, and press PLAY.

7. Your device powers off when it finds the correct code. Then, choose one of the following options:

  • Save code and exit – Press the ENTER key on the remote to program the code in the remote and the mode key flashes three times indicating successful entry.
  • Step forward – Press the fast-forward (FF) key on the remote to step ahead through the codes one at a time. Then, return to step 6.
  • Step backward – Press the rewind (REW) key on the remote to step back through the codes one at a time. Then, return to step 6.
  • Exit without saving the code – Press the EXIT key on the remote. The selected mode key flashes three times and returns to normal operation.
  • Send the current code – Press the POWER key on the remote to send the current code. If the device turns back on, press the ENTER key. If the device does not turn on, return to step 6.
  • Continue with auto-search function – Press the PLAY key on the remote to continue with the auto-search function. Then, return to step 6.

AUTO-SEARCHING THE CODE LIBRARY FOR AUX MODE CODES (Program Code 922)

1. Turn on the device that you want to assign to the AUX key.
2. Point the remote at the device.
3. Press and while holding the AUX key press the OK key.
4. Release both the AUX and the OK keys and all the mode keys will blink twice.
5. Enter the programming code 922 by pressing the numeric keys on the remote. The AUX key
blinks twice to indicate a successful entry.
6. Press the PLAY key, choose one of the following device categories and then, using the
number keys on the remote, press its assigned number (1-4) based on the following list:

  • 1. = VCR
  • 2. = Receiver/Tuners
  • 3. = Amplifiers
  • 4. = HTIB (Home Theater in a Box)

7. Point the remote toward the device and press PLAY.

8. Your device powers off when it finds the correct code. Then choose one of the following options:

  • Save code and exit – Press the ENTER key on the remote to program the code in the remote and the mode key flashes three times indicating successful entry.
  • Step forward – Press the fast-forward (FF) key on the remote to step ahead through the codes one at a time. Then, return to step 7.
  • Step backwards – Press the rewind (REW) key on the remote to step back through the codes one at a time. Then, return to step 7.
  • Exit without saving the code – Press the EXIT key on the remote. The selected mode key flashes three times and returns to normal operation.
  • Send the current code – Press the POWER key on the remote to send the current code. If the device turns back on, press the ENTER key. If the device does not turn on, return to step 7.
  • Continue with auto-search function – Press the PLAY key on the remote to continue with the auto-search function. Then, return to step 7.

How do you program a universal remote?

Programming a universal remote doesn’t need to be a daunting task. There are three common programming options that make setting up your universal remote simple.

Auto-programming

Auto-programming, also called auto code search, allows you to program your remote without needing any additional information, like remote codes. To auto-program your remote, follow these easy steps:

  1. Power on the TV or other device you’d like to connect to.
  2. Insert batteries into your remote and point at the device.
  3. Press and release the correct device button on your remote for the device you’re connecting. For example, if you’re connecting to a TV, press the TV button.
  4. Now press the power button and the device button simultaneously. Hold until the power light on the device turns off and then back on.
  5. Press and release the play button and wait five seconds to see if the device you’re connecting to turns off. If so, you found the correct code. If not, repeat the process. The remote will try a new batch of codes every time you hit the play button, so be sure to give it a moment to cycle through them all.
  6. Press and release the reverse (rewind) button. This should turn the device back on. If not, repeat the process until it finds the correct code.
  7. Press the stop button to save the code.
  8. Test out several functions to ensure they are working correctly and then start using your remote.

You can download Program Universal Remote PDF by going through the following download button.


Program Universal Remote PDF Download Link

RELATED PDF FILES